NEWS: Eachine Minicube (9.4g, F3 FC + betaOSD, 4-in-1 10A Dshot600, FrSky/DSMX/FlySky)

What a concentration of all technologies into this 9.4g cube !!!!:
With the Eachine Minicube, it’s simple you have everything: F3 board integrating betaflight OSD, strong 4-in-1 10A ESC (1-2S system) Dshot600 compatible !!! and 3 type of receivers: FrSKy (D8+telemetry)/ DSMX/ FlySly (AFHDS-2A). The bundle is just great for compact < 100mm machine with some 1103/1104 brushless motor. The perfect AIO camera can be this new Eachine model with a 4 pin connector for OSD pluggin: I hope now new Eachine brushless racer will integrate this Minicube. Probably yes.

Brand name: Eachine
Mount hole: 20mm*20mm
Size: 27mm*27mm*20mm
Weight: 9.4g


1. Eachine Minicube Receiver

1). Eachine Minicube DSM2/ DSMX satellite Receiver
Frequency range: 2.403-2.479Ghz
Input power: 5V
Response time: 22ms / 11MS
Resolution: 2048
Display method: LED
Operating voltage: 3.3V
Working current: 60MA
Size: 27mm*27mm*7mm
Mount hole:20mm*20mm
Weight: 3.1 g
Antenna length: 100mm
Data format: Serial port
Protocol: DSM2/DSMX
Distance: no ground interference (1 m from the ground ) > 300m
Uses: indoor small aircraft.
Compatible Transmitters: DSM2 / DSMX series of remote control


2). Eachine Minicube Flysky 8CH AFHDS2A receiver
Channels: PPM 8CH
Model type: Multi-rotor
Frequency range: 2.408-2.475GHz
2.4GHz system: AFHDS 2A
Work Mode: PPM
Transfer method: FHSS
Built-in Buzzer (Low voltage alarm) Configure by Betaflight configurator
Antenna length: 100mm
No ground interference ( Transmitting and receiving 1 m from the ground): >300m
Working current: 40mA
Size: 27*27*7mm
Mount hole:20mm*20mm
Weight: 3.1g
Compatible Transmitter: Compatible with FS-i4, FS-i6, FS-i6S, FS-i6X, FS-i10, FS-GT2E, FS-GT2G, FS-GT2F


3). Eachine Minicube Frsky Compatible 2.4G 8CH Receiver:

Frequency range: 2.403-2.479Ghz
Channels: 8CH
Work mode :D8 Mode
Output: SBUS
Antenna length: 100mm
No ground interference ( Transmitting and receiving 1 m from the ground): >500m
Built-in Buzzer (Low voltage alarm) Configure by Betaflight configurator
Working current: 80mA
Dimensions: 27*27*7mm
Weight: 3.5g
Compatible with FRSKY ACCST
Compatible with X9D(Plus)DJT/DFT/DHT
Telemetry: RSSI, 1S-3S voltage (A1), 1S-3S voltage (A2)



2. Eachine Minicube F3 6DOF Flight Controller:
Size: 27mm*27mm*5mm
Mount hole: 20mm*20mm
Processor: STM32 F303 MCU
Sensor: SPI Sensor MPU6000
Built-in Betaflight OSD ( Batt voltage, RSSI , Artificial Horizon , Fly mode , -Flytime, Craft name etz.)
Firmware version: Betaflight 3.1 Dshot ready
Target: OmnibusF3


3. Eachine Minicube 10A BLHeli_S 4 In 1 ESC:

Size: 27mm*27mm*5mm
Mount hole: 20mm*20mm
Firmware version: BLHELI_S 16.5
BB2, 48MHZ Chip
Lipo Battery: 1-2S
Con. Current: 10A
Peak Current: 15A (10S)
BEC: 5V @0.1A
Programming: YES
Betaflight passtrough ready
Dshot600 ready(Default)
Support oneshot42 oneshot125 Multishot Dshot
Damped light on

STM32 F303MCU + BLHELI_S ESC make your Operating feel more stabilly and silky
Jaw-dropping flight performance
LED_STRIP solder pin
Cleanflight/Betaflight support
Acro mode / Air mode /Angle mode support
Built-in OSD(Using F3 MCU controls OSD over SPI bus in DMA mode)
OSD Configuration has been include in BETAFLIGHT GUI
Radio Stick to control PID Tunes

Package included:
1 x Minicube Receiver
1 x Minicube F3 6DOF Flight Controller
1 x Minicube 10A BLHeli_S 4 In 1 ESC


Leave a Comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.